Kenwood XD-402 Manuel d'utilisateur Page 16
- Page / 64
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
XD-SERIES (En)
16
Preparation section
Operation of remote control unit
Loading batteries
1 Remove the cover. 3 Close the cover.
÷ Insert two R6 (“AA”-size) batteries
following the polarity indications.
2 Insert batteries.
Operation
Plug the power cord into the mains power outlet and
press the on/standby (
POWER) key of the remote
control unit to turn power ON. After the power has been
turned ON, press the desired key.
To turn power off, press the on/standby( POWER) key
again.
The power mode enters the STANDBY mode in which
the “STANDBY” indicator lights up. (The “TIMER” in-
dicator also lights in this mode if a timer program has
been activated.)
÷ When pressing more than one remote control keys
successively, press the keys securely by leaving an
interval of 1 second or more between keys.
1.The provided batteries are intended for use in operation checking, and their service life may be short.
2.When the remote controllable distance becomes short, replace both of the batteries with new ones.
3.If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote
sensor, malfunction may occur. In such a case, change the installation position to avoid malfunction.
Operating range
(approx.)
Remote sensor
2
1
Notes
Notes
CHANNEL
SPACE freq.
Area
1
2
USA, Canada and South
American countries
Other countries
FM : 100 kHz
AM : 10 kHz
FM : 50 kHz
AM : 9 kHz
The space between radio channels has been set to the
one that prevails in the area to which the system is
shipped. However, if the current channel space setting
does not match the setting in the area where the sys-
tem is to be used, for instance when you move from
area 1 or area 2 shown in the following table or vice
versa, proper reception of AM/FM (MW/FM) broad-
casts cannot be expected. In this case, change the chan-
nel space setting in accordance with your area by re-
ferring to the following table.
CHANNEL SPACE setting
(Except for the U.S.A., Canada, U.K., Europe, Australia and Russia)
1 Select the TUNER input.
2 While holding the SELECT key depressed, turn
the SOUND CONTROL jog dial to select the
system mode.
ENTER
F0M100/AM1
F9M 50/AM
SELECT
30
˚
6m
30
˚
÷ The “AM” display is variable depending on the model
(country or area), and “MW” may be displayed in
some areas.
1 “FM100/AM10 kHz” STEP,
2 “FM 50 /AM 9 kHz” STEP,
3 Establish the selection.
S
O
U
N
D
C
O
N
T
R
O
L
- XD-SERIES 1
- Before applying power 2
- Contents 3
- Knowledge section 3
- Basic section 3
- IMPORTANT SAFEGUARDS 4
- POWER OFF! 5
- Special features 6
- Handling of discs and tapes 7
- System connection 8
- Malfunction of microcomputer 9
- Speakers 9
- Caution regarding placement 9
- Speaker and TV installation 9
- Super woofer 10
- Surround (rear) speakers 11
- FM outdoor antenna 11
- Controls and indicators 12
- Cassette deck unit 13
- Receiver 13
- • •• • • • • • • • 14
- Remote control Unit 15
- Loading batteries 16
- Operation 16
- CHANNEL SPACE setting 16
- Operation of jog dials 17
- Let’s put out some sound 18
- V9olume 1 19
- Playback of CD 20
- C0D01 0:0 21
- Playback of tape 22
- (Main unit only) 23
- (XD-4....series only) 23
- T0APE 000 24
- (DPSS)(XD-5....series only) 25
- 1. Select the broadcast band 26
- 2. Selecting the tuning mode 26
- 3. Select a station 26
- -0-FM 89.0 27
- Let's record 28
- 5. Start recording 29
- Points in CD recording 30
- Beat cancel function 30
- Copying tape 31
- Check the programmed tracks 33
- Enter it 33
- Repeated playback 34
- To repeat all discs 35
- Random playback 36
- Note before the use of RDS 37
- Select the PTY search mode 38
- Start the search 39
- Auto preset the stations 40
- Receive an RDS station 40
- Application section 41
- NoteNote 42
- Select “Recording Options” 43
- Start recording 43
- (CD ONE TRACK RECORDING) 43
- D isc No.1Sselect Di 44
- (CD PROGRAM RECORDING) 45
- Balance adjustment 46
- Input level adjustment 47
- Play desired music 48
- Asdjust Ba Bass -8 49
- Select “Clock Options” 50
- Select “Adjust Time” 50
- Enter the figure of hour 50
- Enter the figure of minute 50
- Sleep timer (SLEEP) 51
- Operate easy To use Timer 52
- Timer programming 53
- Enter the ON time 54
- Enter the OFF time 54
- ON/STANDBY 55
- Important Items 56
- In case of difficulty 57
- Cassette deck 58
- CD player 59
- CAUTION : 60
- Specifications 61
- For your records 64
Produits connexes et manuels pour Lecteurs de CD Kenwood XD-402
(60 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.235 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels