Kenwood VR-5080 Manuel d'utilisateur télécharger pdf (Page 50)

Receiver Setup

Chapter Three: Using Receiver’s Front Panel to Set Up the Speakers

You can also perform the Speaker Setup and program pre-

set radio stations using the receiver’s front panel. (If you

have already set up the speakers or programmed radio sta-

tions using Remote Control unit you don’t have to repeat

the procedures using the front panel.)

Since you still must use Remote Control unit to identify

and set up your source devices for control, we recommend

that you use it for all setup procedures.

• Do not operate Remote Control unit while you are per-

forming Speaker Setup on the receiver’s front panel.

Preparation for setup

Most of the front panel control buttons are located inside

the panel door. Make the following preparation for setup

on the receiver. Open the panel door by pushing the lower

part of the panel door.

Speaker Setup

1. Press the SET UP button (SOUND button) until

SUBWOOFER ON appears on the receiver’s display (for

more than 2 seconds).

A. If your system has a powered subwoofer, leave the

receiver set this way and proceed to step 2.

B. If your system does not have a powered subwoofer,

press either MULTI CONTROL (ﬁ/%) button once.

The receiver’s display will read SUBWOOFER OFF.

2. Press the SET UP button once more. The receiver’s dis-

play will read FRONT NML/THX.

A. If your left and right front speakers are not capable

of producing clean, deep bass energy at output lev-

els that match those produced by a typical powered

subwoofer, leave the receiver set this way and pro-

ceed to step 3. (Most left and right speakers should

be considered NML/THX.)

B. If your left and right speakers are very large, and ca-

pable of reproducing clean, deep bass energy at out-

put levels that match those produced by a typical

powered subwoofer, press either MULTI CONTROL

(ﬁ/%) button once. The receiver’s display will read

FRONT LARGE.

NOTE: If you set your front speakers to LARGE, the

subwoofer may not output audio depending

on the setups of the rest of the speakers, the

input signal and the listen mode. See step 6.

3. Press the SET UP button once more. The receiver’s dis-

play will read CENTER NML/THX.

A. If your center speaker is not capable of producing

clean, deep bass energy at output levels that match

those produced by a typical powered subwoofer, leave

the receiver set this way and proceed to step 4. (Just

about all center speakers should be considered NML/

THX.)

B. If your center speaker is very large, and capable of

reproducing clean, deep bass energy at output levels

that match those produced by a typical powered

subwoofer, press either MULTI CONTROL (ﬁ/%)

button repeatedly until the receiver’s display reads

CENTER LARGE.

C. If your speaker system doesn’t have a center speaker,

SPEAKERS

INPUT

MODE

CD 2/TAPE 2

MONITOR

LISTEN

MODE THX

SET UPDISPLAYRF BANDRF

ON/OFF

SOUND

MULTI

CONTROL

ﬁ%

P.CALL MEMORY AUTO BAND

ﬁ%

Button layout

Panel door

Push the lower part of the

panel door.

press either MULTI CONTROL (ﬁ/%) button repeat-

edly until the receiver’s display reads CENTER OFF.

NOTE: If your front speakers are set to NML/THX, you

can only set the center speaker to NML/THX

or OFF.

4. Press the SET UP button once more. The receiver’s dis-

play will read SURR NML/THX.

A. If your surround speakers are not capable of produc-

ing clean, deep bass energy at output levels that

match those produced by a typical powered

subwoofer, leave the receiver set this way and pro-

ceed to step 5. (Just about all surround speakers

should be considered NML/THX.)

B. If your surround speakers are very large, and capable

of reproducing clean, deep bass energy at output lev-

els that match those produced by a typical powered

subwoofer, press either MULTI CONTROL (ﬁ/%)

button repeatedly until the receiver’s display reads

SURR LARGE.

C. If your speaker system doesn’t have surround speak-

ers, press either MULTI CONTROL (ﬁ/%) button re-

peatedly until the receiver’s display reads SURR OFF.

NOTE: If your front speakers are set to NML/THX, you

can only set the surround speakers to NML/

THX or OFF.

5. Press the SET UP button once more. The receiver’s dis-

play will read S.BACK NML/THX.

NOTE: If your surround speakers are set to OFF, the

surround back speakers are automatically set

to OFF and the receiver skips to step 6.

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

Kenwood VR-5080 Manuel d'utilisateur Page 50

Commentaires sur ces manuels

Produits connexes et manuels pour DVR de voiture Kenwood VR-5080