Kenwood TS-590S Manuel d'utilisateur télécharger pdf (Page 35)

6 ENHANCED COMMUNICATIONS

• Press [SCAN (SG.SEL)] or [CLR] to stop

scanning while the CTCSS frequency ID scan is

active.

• Press [SCAN (SG.SEL)] again to resume

scanning.

Note: Received signals are audible while scanning is in

progress.

CROSS TONE

Use this feature when using different uplink and

downlink tones to access a repeater. You can set a

transmission Tone frequency and reception CTCSS

frequency to different frequencies.

To set the transmission tone:

1 Press [A/B (A=B)] to select VFO A or VFO B.

2 Select your desired transmission frequency.

3 Press [FM/AM (FM-N)] to select FM.

4 Press [AGC/T (SEL)] until “

” appears.

5 Press and hold [AGC/T (SEL)], then rotate the

MULTI/CH control to select your desired Tone

frequency.

6 Press and hold [AGC/T (SEL)] or press [CLR] to

complete the setting.

To set the reception tone:

1 Press [A/B (A=B)] to select the other VFO.

2 Select your desired reception frequency.

3 Press [FM/AM (FM-N)] to select FM.

4 Press [AGC/T (SEL)] until “ ” appears.

5 Press and hold [AGC/T (SEL)], then rotate the

MULTI/CH control to select your desired CTCSS

frequency.

6 Press and hold [AGC/T (SEL)] or press [CLR] to

complete the setting.

To set the Cross tone:

1 Press [SPLIT].

• “SPLIT” appears on the display.

2 Press [AGC/T (SEL)] until “

” appears.

Note: hen the cross tone function is ON, the Tone and CTCSS

frequency cannot be changed. To change the Tone or CTCSS

frequency, press [AGC/T (SEL)] to turn Tone or CTCSS ON,

then change the setting.

8 Turn the MULTI/CH control to select the

appropriate CTCSS frequency.

• The selectable CTCSS frequencies are listed in

the table below.

9 Press and hold [AGC/T (SEL)] or press [CLR] to

complete the setting.

No.

Freq.

(Hz)

No.

Freq.

(Hz)

No.

Freq.

(Hz)

No.

Freq.

(Hz)

00 67.0 11 97.4 22 141.3 33 206.5

01 69.3 12 100.0 23 146.2 34 210.7

02 71.9 13 103.5 24 151.4 35 218.1

03 74.4 14 107.2 25 156.7 36 225.7

04 77.0 15 110.9 26 162.2 37 229.1

05 79.7 16 114.8 27 167.9 38 233.6

06 82.5 17 118.8 28 173.8 39 241.8

07 85.4 18 123.0 29 179.9 40 250.3

08 88.5 19 127.3 30 186.2 41 254.1

09 91.5 20 131.8 31 192.8 -- --

10 94.8 21 136.5 32 203.5 -- --

You will hear calls only when the selected tone is

received. To answer the call, press and hold Mic

[PTT], then speak into the microphone.

Skip steps 7 and 8 if you have already programmed

the appropriate CTCSS frequency.

Note:

◆ When using split-frequency operation, select FM mode on

both VFOs to use CTCSS.

◆ You can select a CTCSS frequency independent of a tone

frequency.

◆ You cannot use the CTCSS function with the Tone function.

CTCSS FREQUENCY ID SCAN

This function scans through all CTCSS frequencies to

identify the incoming CTCSS frequency on a received

signal. You may find this useful when you cannot

recall the CTCSS frequency that the other persons in

your group are using.

1 While the CTCSS function is ON, press and hold

[AGC/T (SEL)].

• The current CTCSS frequency appears.

2 Press [SCAN (SG.SEL)] to activate the CTCSS

frequency ID scan.

• While the transceiver is receiving a signal, “ ”

blinks and every CTCSS frequency is scanned.

When the CTCSS frequency is identified, the

transceiver stops scanning and the identified

frequency is displayed.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 91 92

Commentaires sur ces manuels

Pas de commentaire

Kenwood TS-590S Manuel d'utilisateur Page 35

Commentaires sur ces manuels

Produits connexes et manuels pour Radio Kenwood TS-590S