Kenwood TS-590S Manuel d'utilisateur Page 67
- Page / 92
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
59
12 OPERATOR CONVENIENCES
• BT in Morse code sounds and “AP 1 –”
appears.
• To quit recording your message, press [CLR].
3 Press [MIC (CAR)], then rotate the MULTI/CH
control to adjust the microphone gain so that the
voice input level is not beyond the ALC level zone.
4 Hold [CH1 (REC)] and speak into your
microphone.
• Four channels are available for recording
messages. Press [CH2 (REC)], [CH3 (REC)],
or [RX/4 (REC)] in place of [CH1 (REC)], in
steps 3 and 4 to record the message on a
different channel.
• If Constant Recording is active, [RX/4 (REC)] is
unavailable for message recording.
5 Release the key when you have finished recording
your message.
• When the maximum recording time passes,
recording automatically stops.
• The contents of the channel is overwritten with
the new message.
• “WRITING” appears while the transceiver is
storing the message data to the VGS-1 flash
memory.
6 Repeat steps 2 to 5 to record a message on
another channel.
Note: Pressing [ ] cancels the recording in progress and
clears the memory channel.
MESSAGE PLAYBACK
You can play back the message in channel 1, 2, 3, or
4 to check or send them. It is also possible to make
a longer message by consecutively playing back the
messages of more than one channel, linking them
together.
You can even repeatedly send a longer, linked
message by using the Repeat function. To switch
this function ON, access Menu No. 56 and select “on”
(default is OFF). Then, select the repeat interval time
in Menu No. 57 (default is 10 seconds).
Note:
◆ Pressing [ ] cancels the playback in progress.
◆ The settings in Menu Nos. 56 and 57 are shared with CW
Message Playback described in “CW MESSAGE MEMORY”
{page 34}.
■ Checking Messages
1 Select SSB, FM, or AM mode.
• Select the same mode when you recorded
the message.
• Confirm that the VOX function is OFF.
2 Press [CH1 (REC)], [CH2 (REC)], [CH3
(REC)], or [RX/4 (REC)], depending on which
channel you want to check.
• For example, “AP 1– – –” appears while
playing back the message in channel 1.
• To interrupt playback, press [CLR].
• When Menu No. 56 is "oFF", pres and
hold the current playback channel key to
repeatedly play back the message saved
to that key (A display such as “AP 1111”
appears for the channel key you pressed.).
To cancel the playback, press any channel
key or [CLR].
3 To play back another message in sequence,
press the corresponding key ([CH1 (REC)],
[CH2 (REC)], [CH3 (REC)], or [RX/4 (REC)])
while the first message is being played.
• Repeat playback, by pressing and holding
the keys, does not work during consecutive
message playback.
• Up to 4 channels can be queued.
■
Sending Messages
1 Select SSB, FM, or AM mode.
• Select the same mode when you recorded
the message.
2 Press [VOX (LEV)] to switch VOX ON or OFF.
• If you switched VOX ON, skip step 3.
3 Press [SEND] or hold Mic [PTT].
4 Press [CH1 (REC)], [CH2 (REC)], [CH3
(REC)], or [RX/4 (REC)], depending on which
channel you want to use.
• For example, “AP 1– – –” appears while
playing back the message in channel 1.
• To interrupt playback, press [CLR].
5 To play back another message in sequence,
press the corresponding key ([CH1 (REC)],
[CH2 (REC)], [CH3 (REC)], or [RX/4 (REC)])
while the first message is being played.
• Up to 4 channels can be queued.
6 If you pressed [SEND] or Mic [PTT] in step 3,
press [SEND] again or release Mic [PTT].
■
Erasing a Recorded Message
1 Press and hold [CH1 (REC)], [CH2 (REC)],
[CH3 (REC)], or [RX/4 (REC)] to select the
message you want to erase.
• “AP n – –” appears, where “n” represents the
channel number.
2 To erase the recorded message, press and hold
the same key as in step 1 ([CH1 (REC)], [CH2
(REC)], [CH3 (REC)], or [RX/4 (REC)]) while
simultaneously pressing [CLR].
• A beep sounds and the message is erased.
■ Changing Inter-message Interval Time
For repetitive message playback, you can change
the interval between each series of messages.
Use Menu No. 57, and select the interval time in
the range of 0 to 60 seconds.
- INSTRUCTION MANUAL 1
- THANK YOU 3
- FEATURES 3
- NOTICE TO THE USER 3
- BEFORE STARTING 3
- MARKET CODES 3
- WRITING CONVENTIONS FOLLOWED 4
- SUPPLIED ACCESSORIES 4
- PRECAUTIONS 5
- CONTENTS 6
- INSTALLATION 9
- UTILIZING THE BAIL 10
- REPLACING FUSES 10
- ACCESSORY CONNECTIONS 10
- 1 INSTALLATION 11
- GETTING ACQUAINTED 12
- —— F —— 13
- 2 GETTING ACQUAINTED 13
- —— D —— 13
- —— E —— 13
- LCD DISPLAY 15
- REAR PANEL 17
- MICROPHONE 17
- OPERATING BASICS 18
- SELECTING A BAND 19
- SELECTING A MODE 19
- MULTI-FUNCTION METER 20
- ADJUSTING THE SQUELCH 20
- TUNING A FREQUENCY 20
- TRANSMITTING 21
- MENU SETUP 22
- MENU CONFIGURATION 23
- 4 MENU SETUP 24
- CHARACTER ENTRY 28
- BASIC COMMUNICATIONS 29
- AM TRANSMISSION 30
- NARROW BANDWIDTH FOR FM 30
- CW TRANSMISSION 30
- CARRIER LEVEL 31
- POWER ON MESSAGE 31
- ENHANCED COMMUNICATIONS 32
- FM REPEATER OPERATION 33
- FM CTCSS OPERATION 34
- CROSS TONE 35
- COMMUNICATING AIDS 36
- 7 COMMUNICATING AIDS 37
- AGC (AUTOMATIC GAIN CONTROL) 37
- TRANSMISSION 38
- SPEECH PROCESSOR 39
- TX Equalizer (SSB/ AM/ FM) 40
- Frequency Response Curves 40
- CW BREAK-IN 41
- ELECTRONIC KEYER 41
- RISE TIME OF CW 42
- AUTO WEIGHTING 42
- BUG KEY FUNCTION 42
- CW MESSAGE MEMORY 42
- FREQUENCY CORRECTION FOR CW 43
- AUTO CW TX IN SSB MODE 44
- MIC UP/ DWN KEY PADDLE MODE 44
- DATA COMMUNICATIONS 45
- REJECTING INTERFERENCE 46
- 9 REJECTING INTERFERENCE 47
- AUTO NOTCH FILTER (SSB) 47
- BEAT CANCEL (SSB/ AM) 47
- NOISE REDUCTION (ALL MODES) 47
- NOISE BLANKER 48
- PRE-AMPLIFIER 48
- ATTENUATOR 48
- CW REVERSE (RECEPTION) 48
- MEMORY FEATURES 49
- 10 MEMORY FEATURES 50
- MEMORY TRANSFER 50
- MEMORY RECALL AND SCROLL 50
- STORING FREQUENCY RANGES 51
- QUICK MEMORY 52
- NORMAL SCAN 54
- 11 SCAN 55
- PROGRAM SCAN PARTIALLY SLOWED 55
- MEMORY SCAN 56
- QUICK MEMORY SCAN 57
- OPERATOR CONVENIENCES 58
- AUTO MODE 59
- BEEP FUNCTION 60
- PANEL KEY DOUBLE FUNCTION 61
- RESPONSE TIME 61
- LINEAR AMPLIFIER CONTROL 61
- LOCK FUNCTIONS 61
- PROGRAMMABLE FUNCTION KEYS 62
- TIME-OUT TIMER 63
- TRANSVERTER 63
- DSP RX EQUALIZER 63
- TX MONITOR 64
- TX POWER 64
- QUICK DATA TRANSFER 64
- COMPUTER CONTROL 65
- STORAGE UNIT 66
- 12 OPERATOR CONVENIENCES 67
- MESSAGE PLAYBACK 67
- VOICE GUIDE 68
- CONSTANT RECORDING 68
- EMERGENCY CALL (K TYPE ONLY) 70
- CROSSBAND REPEATER 71
- DX PACKETCLUSTER TUNE 71
- SKY COMMAND SYSTEM II DIAGRAM 72
- PREPARATION 72
- TERMINAL DESCRIPTIONS 73
- REMOTE CONNECTOR 74
- EXT.AT CONNECTOR (for AT-300) 74
- MIC CONNECTOR 74
- COMPUTER 75
- COMPATIBLE TRANSCEIVER 75
- ANTENNA TUNER 77
- TNC AND MCP 77
- RS-232C cross cable 78
- INSTALLING OPTIONS 79
- SO-3 TCXO 80
- MB-430 MOBILE BRACKET 81
- TROUBLESHOOTING 82
- 15 TROUBLESHOOTING 84
- MICROPROCESSOR RESET 86
- OPERATION NOTICES 87
- OPTIONAL ACCESSORIES 88
- SPECIFICATIONS 89
- 17 SPECIFICATIONS 90
- Transmitter 90
- Receiver 90
Produits connexes et manuels pour Radio Kenwood TS-590S
(4 pages)
(4 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.696 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels