Kenwood TS-590S Manuel d'utilisateur Page 70
- Page / 92
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
62
12 OPERATOR CONVENIENCES
VOICE3 Announcements
SWR meter ALC meter
Dot
position
Announcement
Dot
position
Announcement
1 R 1.0 0 A 0
2 ~ 6 R 1.5 1 A 1
7 ~ 11 R 2.0 2 A 2
12 ~ 16 R 3.0 ~ ~
17 ~ 24 R 5.0 13 A 13
25 ~ 30
R OVER
14 A 14
15 ~ A OVER
COMP meter
Dot
position
Announcement
0 C 0 dB
1 ~ 10 C 10 dB
11 ~ 20
C 20 dB
21 ~ 30
C OVER
■ Voice Guide Announcement Volume
Turning the AF control does not change the
volume for the Voice Guide announcement. To
change the announcement volume , access Menu
No. 06 and select the volume level from “1” to “7”
or “oFF”.
■ Voice Guide Announcement Speed
If you feel the Voice Announcement speed is
too slow or too fast, you can adjust the Voice
Announcement speed. Five different speeds can
be configured. Access Menu No. 07 and select “0”
to “4”, where 0 is the slowest speed and 4 is the
fastest. The default speed is 1.
■ Voice Guide Announcement Language
If you mistakenly change the announcement
language, you can change it back to English by
accessing Menu No. 08 and selecting “EN”.
EMERGENCY CALL (K TYPE ONLY)
Section 97.401(d) of the regulations governing
amateur radio in the United States permit emergency
amateur communications on 5167.5 kHz by stations
in or within 92.6 km of the state of Alaska. This
frequency is for use only when the immediate safety
of human life and/or property are threatened, and is
never to be used for routine communications.
Press [EMERGENCY] to change to the Emergency
channel (5167.5 kHz/ USB).
• [EMERGENCY] can be programmed onto a PF
key.
• When entering Emergency mode, “EMERGENCY”
momentarily appears on the sub-display.
Status Announcement
Press [A/B (A=B)] +
[
], then turn the
MULTI/CH control
Reset confirmation
during VFO reset
2
“VFO reset?”
Press [A/B (A=B)] +
[ ], then turn the
MULTI/CH control
Reset confirmation
during Full reset
2
“Full reset?”
1
Announced when operating in Split-frequency mode.
2
Announced even when the auto Voice announcement is OFF.
3
When auto Voice announcement is ON, various configuration
images appear on the display. When modifications are made to
these settings, the new setting is announced.
VOICE2:
• Pressing [PF] will announce the current state of
the S meter/ RF meter.
• During a voice announcement, pressing [PF] will
cancel the announcement.
VOICE2 Announcements
S meter PWR meter
Dot
position
Announcement
Dot
position
Announcement
0S 00P 0
1 ~ 3 S 1 1 ~ 3 P 5
4 ~ 5 S 2 4 ~ 6 P 10
6 S 3 7 ~ 12 P 25
7 ~ 8 S 4 13 ~ 18 P 50
9 S 5 19 ~ 23 P 75
10 ~ 11 S 6 24 ~ 30 P 100
12 S 7
13 ~ 14 S 8
15 S 9
16 ~ 19 10 dB
20 20 dB
21 ~ 24 30 dB
25 40 dB
26 ~ 29 50 dB
30 60 dB
VOICE3:
• Pressing [PF] will announce the current state of
the SWR meter/ ALC meter/ COMP meter.
• During a voice announcement, pressing [PF] will
cancel the announcement.
- INSTRUCTION MANUAL 1
- THANK YOU 3
- FEATURES 3
- NOTICE TO THE USER 3
- BEFORE STARTING 3
- MARKET CODES 3
- WRITING CONVENTIONS FOLLOWED 4
- SUPPLIED ACCESSORIES 4
- PRECAUTIONS 5
- CONTENTS 6
- INSTALLATION 9
- UTILIZING THE BAIL 10
- REPLACING FUSES 10
- ACCESSORY CONNECTIONS 10
- 1 INSTALLATION 11
- GETTING ACQUAINTED 12
- —— F —— 13
- 2 GETTING ACQUAINTED 13
- —— D —— 13
- —— E —— 13
- LCD DISPLAY 15
- REAR PANEL 17
- MICROPHONE 17
- OPERATING BASICS 18
- SELECTING A BAND 19
- SELECTING A MODE 19
- MULTI-FUNCTION METER 20
- ADJUSTING THE SQUELCH 20
- TUNING A FREQUENCY 20
- TRANSMITTING 21
- MENU SETUP 22
- MENU CONFIGURATION 23
- 4 MENU SETUP 24
- CHARACTER ENTRY 28
- BASIC COMMUNICATIONS 29
- AM TRANSMISSION 30
- NARROW BANDWIDTH FOR FM 30
- CW TRANSMISSION 30
- CARRIER LEVEL 31
- POWER ON MESSAGE 31
- ENHANCED COMMUNICATIONS 32
- FM REPEATER OPERATION 33
- FM CTCSS OPERATION 34
- CROSS TONE 35
- COMMUNICATING AIDS 36
- 7 COMMUNICATING AIDS 37
- AGC (AUTOMATIC GAIN CONTROL) 37
- TRANSMISSION 38
- SPEECH PROCESSOR 39
- TX Equalizer (SSB/ AM/ FM) 40
- Frequency Response Curves 40
- CW BREAK-IN 41
- ELECTRONIC KEYER 41
- RISE TIME OF CW 42
- AUTO WEIGHTING 42
- BUG KEY FUNCTION 42
- CW MESSAGE MEMORY 42
- FREQUENCY CORRECTION FOR CW 43
- AUTO CW TX IN SSB MODE 44
- MIC UP/ DWN KEY PADDLE MODE 44
- DATA COMMUNICATIONS 45
- REJECTING INTERFERENCE 46
- 9 REJECTING INTERFERENCE 47
- AUTO NOTCH FILTER (SSB) 47
- BEAT CANCEL (SSB/ AM) 47
- NOISE REDUCTION (ALL MODES) 47
- NOISE BLANKER 48
- PRE-AMPLIFIER 48
- ATTENUATOR 48
- CW REVERSE (RECEPTION) 48
- MEMORY FEATURES 49
- 10 MEMORY FEATURES 50
- MEMORY TRANSFER 50
- MEMORY RECALL AND SCROLL 50
- STORING FREQUENCY RANGES 51
- QUICK MEMORY 52
- NORMAL SCAN 54
- 11 SCAN 55
- PROGRAM SCAN PARTIALLY SLOWED 55
- MEMORY SCAN 56
- QUICK MEMORY SCAN 57
- OPERATOR CONVENIENCES 58
- AUTO MODE 59
- BEEP FUNCTION 60
- PANEL KEY DOUBLE FUNCTION 61
- RESPONSE TIME 61
- LINEAR AMPLIFIER CONTROL 61
- LOCK FUNCTIONS 61
- PROGRAMMABLE FUNCTION KEYS 62
- TIME-OUT TIMER 63
- TRANSVERTER 63
- DSP RX EQUALIZER 63
- TX MONITOR 64
- TX POWER 64
- QUICK DATA TRANSFER 64
- COMPUTER CONTROL 65
- STORAGE UNIT 66
- 12 OPERATOR CONVENIENCES 67
- MESSAGE PLAYBACK 67
- VOICE GUIDE 68
- CONSTANT RECORDING 68
- EMERGENCY CALL (K TYPE ONLY) 70
- CROSSBAND REPEATER 71
- DX PACKETCLUSTER TUNE 71
- SKY COMMAND SYSTEM II DIAGRAM 72
- PREPARATION 72
- TERMINAL DESCRIPTIONS 73
- REMOTE CONNECTOR 74
- EXT.AT CONNECTOR (for AT-300) 74
- MIC CONNECTOR 74
- COMPUTER 75
- COMPATIBLE TRANSCEIVER 75
- ANTENNA TUNER 77
- TNC AND MCP 77
- RS-232C cross cable 78
- INSTALLING OPTIONS 79
- SO-3 TCXO 80
- MB-430 MOBILE BRACKET 81
- TROUBLESHOOTING 82
- 15 TROUBLESHOOTING 84
- MICROPROCESSOR RESET 86
- OPERATION NOTICES 87
- OPTIONAL ACCESSORIES 88
- SPECIFICATIONS 89
- 17 SPECIFICATIONS 90
- Transmitter 90
- Receiver 90
Produits connexes et manuels pour Radio Kenwood TS-590S
(4 pages)
(4 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.257 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels