Kenwood TS-590S Manuel d'utilisateur télécharger pdf (Page 36)

COMMUNICATING AIDS

RECEPTION

SELECTING YOUR FREQUENCY

In addition to turning the Tuning control or pressing

Mic [UP]/ [DWN], there are several other ways

to select your frequency. This section describes

additional methods of frequency selection that may

save you time and effort.

■

Direct Frequency Entry

When the desired frequency is far removed from

the current frequency, directly entering a frequency

from the numeric keypad is usually the fastest

method.

1 Press [ENT].

• “ - - . - - - . - - ” appears.

2 Press the numeric keys ([50 (0)] to [28 (9)]) to

enter your desired frequency.

• Pressing [ENT] at any time fills the

remaining digits (the digits you did not enter)

with 0 and completes the entry.

To select 1.85 MHz for example, press

[ENT], [50 (0)], [1.8 (1)], [24 (8)], [14 (5)],

then press [ENT] to complete the input (6

key strokes).

• Pressing [CLR] before pressing [ENT]

cancels the entry and restores the current

VFO frequency.

Note:

◆ You can enter a frequency in the range of 30.00 kHz

to 59.999.99 MHz. Refer to the specifications for the

available frequency range.

◆ Attempting to enter a frequency that is outside the

selectable frequency range causes an alarm to sound

and the entered frequency is rejected.

◆ When the entered frequency does not meet the current

VFO frequency step size requirement, the nearest

available frequency is automatically selected after the

entered frequency is changed.

◆ When the 10 Hz digit (last displayed digit) is entered,

the digit 0 is automatically entered for the 1 Hz digit,

and frequency entry is completed. The 1 Hz digit is not

displayed.

◆ When an entered frequency is accepted, RIT or XIT will

be switched OFF, but the RIT or XIT offset frequency is

not cleared.

■ Frequency Entry History

The last 10 frequencies you entered are stored in

the Frequency Entry History. You can access the

history to easily re-enter a recently used frequency.

1 Press [ENT].

2 Turn the MULTI/CH control.

• The entered frequency along with its log

number appears. The most recent entered

frequency is logged as number E0 and the

oldest frequency is logged as number E9.

3 Press [ENT] to set the selected frequency to

the VFO.

Note: When entering a frequency using the numeric

keys, if you turn the MULTI/CH control in the middle of the

frequency entry, the frequency will be entered into the log.

■ Using the MHz key

You can use the MULTI/CH control to change the

operating frequency in steps of 1 MHz.

1 Press [MHz].

• “ ” appears.

2 Turn the MULTI/CH control.

• Clockwise increases the frequency and

counter-clockwise decreases the frequency.

3 Press [MHz] again to exit.

• “ ” disappears.

If you prefer to change the frequency in steps of

100 kHz or 500 kHz, rather than 1 MHz, access

Menu No. 10 and select 100 kHz, 500 kHz, or

1 MHz.

Note: Even if 100 kHz or 500 kHz is assigned for the [MHz]

key, “ ” appears on the display.

■ Quick QSY

To move up or down the frequency quickly, use the

MULTI/CH control. Turning this control changes

the operating frequency in steps of 5 kHz for SSB/

CW/ FSK/ AM and steps of 10 kHz for FM.

• If you want to change the default frequency

step size, access Menu No. 14 (SSB/CW/FSK),

15 (AM), or 16 (FM). Press [M.IN]/ [SCAN (SG.

SEL)] to select 500 Hz, 1 kHz, 2.5 kHz, 5 kHz,

or 10 kHz for SSB/ CW/ FSK, and 5 kHz, 6.25

kHz, 10 kHz, 12.5 kHz, 15 kHz, 20 kHz, 25 kHz,

30 kHz, 50 kHz, or 100 kHz for AM/ FM. The

default frequency step size is 5 kHz for SSB/

CW/ FSK/ AM and 10 kHz for FM.

• When changing the operating frequency by

using the MULTI/CH control, frequencies

are rounded such that new frequencies are

multiples of the frequency step size. To disable

this function, access Menu No. 12 and select

“oFF” (default is ON).

• Within the AM broadcast band, the step size

automatically defaults to the frequency step

value in Menu No. 13. This frequency step size

can be switched between 9 kHz (“on”) and

5 kHz (“oFF”) via Menu No. 13.

Note: The programmed frequency step size for the

MULTI/CH control is stored independently for the HF and

50 MHz bands. You can also set a different frequency step

size for SSB/ CW/ FSK, AM and FM modes.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 91 92

Commentaires sur ces manuels

Pas de commentaire

Kenwood TS-590S Manuel d'utilisateur Page 36

Commentaires sur ces manuels

Produits connexes et manuels pour Radio Kenwood TS-590S